Bells Bells Posted March 6, 2015 Share Posted March 6, 2015 Hi thereI'm testing C3 wax with 8% f/o. I've been told that when testing a single candle for throw 8% is adequate. But for batches the scent needs to be reduced to 6%. Has anyone else heard of this? Is this right? Quote Link to comment Share on other sites More sharing options...
Trappeur Posted March 6, 2015 Share Posted March 6, 2015 Hello Bells, I've never used more than 6% oil for the C3 and that wax is a beautiful wax with wonderful throw. Trappeur Quote Link to comment Share on other sites More sharing options...
Bells Bells Posted March 6, 2015 Author Share Posted March 6, 2015 Thanks! I've tried 6% and the scent throw wasn't strong at all. I find 8% works great just wondered if the fragrance had to be reduced when making batches. Thanks! 1 Quote Link to comment Share on other sites More sharing options...
Jcandleattic Posted March 6, 2015 Share Posted March 6, 2015 Hi thereI'm testing C3 wax with 8% f/o. I've been told that when testing a single candle for throw 8% is adequate. But for batches the scent needs to be reduced to 6%. Has anyone else heard of this? Is this right?However you test your candles, single candle at a time, or batches, it needs to be consistent or your test results will be skewed. If you are testing a single candle at 8% you should test your batches at 8%. How much is too much per the thread title? Well, that would depend on the wax. Some waxes can hold up to 12% or more before becoming saturated. However, for me personally, and economically, I find in my wax (not C3) 6% is quite sufficient, and if a scent does not perform at that % I dump it. There are too many good fragrances out there to fight a dud. 1 Quote Link to comment Share on other sites More sharing options...
CareBear Posted March 6, 2015 Share Posted March 6, 2015 I aim for the same STRENGTH of SCENT across my candle scents, so the use level of the FO can vary based on the scent and on the supplier. It's impossible to be spot on for all, so clearly there's lots of wiggle room but that's my goal. How much is too much? It depends on for what you are looking and what happens in your candles and how much you are willing to spend in raw materials for your candles. As for 6% for batches and 8% for individual candles I have only this to say - hunh? Quote Link to comment Share on other sites More sharing options...
Candybee Posted March 6, 2015 Share Posted March 6, 2015 That would be weird to test at 8% and then use 6% for your candles. It doesn't make sense so wherever you heard it from its not the best advice for candlemaking. Since I sell candles and want the best scent for them I use 6% as a general rule. There are a few that are the exception. For example I have one I use 4% and one I use 8%. If they don't work at 6% I move on to another fragrance for the most part. Using more fragrance doesn't always mean the candle will smell better. Too much can clog the wick, cause excessive sooting, mushrooms, or you can lose some of the more complex notes. If you are planning to sell then you have to look at the whole picture which includes the cost of using a higher amount of FO. Especially if its not necessary. Quote Link to comment Share on other sites More sharing options...
Mannie Posted March 6, 2015 Share Posted March 6, 2015 Jcandleattic do you use exact 6% or the 1 oz per pound formula? Quote Link to comment Share on other sites More sharing options...
Candybee Posted March 6, 2015 Share Posted March 6, 2015 6% is .96 or rounded off 1oz pp wax. Lots of people use either statement interchangeably. Its when you start doing a ton of candles then you want to calculate it as that small % can add up. 1 Quote Link to comment Share on other sites More sharing options...
Jcandleattic Posted March 6, 2015 Share Posted March 6, 2015 Jcandleattic do you use exact 6% or the 1 oz per pound formula?I do exact 6% because not all of my candlemaking is done in exact lb increments. Quote Link to comment Share on other sites More sharing options...
Candybee Posted March 7, 2015 Share Posted March 7, 2015 I do exact 6% because not all of my candlemaking is done in exact lb increments. Same here! I calculate how much scent I need at 6% by the number of candles I need to make in that scent. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.